ONKYO TX-SR506 Manuel d'utilisateur télécharger pdf (Page 75)

Advanced Setup

—Continued

Tuner

■

AM Freq (on some models)

See “AM Frequency Step Setup (on some models)” on

page 49.

AnalogMulti

■

SW In Sens

Some DVD players output the LFE channel from their

analog subwoofer output at 15 dB higher than normal.

With this setting, you can change the AV receiver’s sub-

woofer sensitivity to match your DVD player. Note that

this setting only affects signals connected to the AV

receiver’s MULTI CH SUBWOOFER jack.

You can select 0 dB, 5 dB, 10 dB, or 15 dB.

If you ﬁnd that your subwoofer is too loud, try the 10 dB

or 15 dB setting.

HDMI

■

AudioTVOut

This setting determines whether audio received by an

HDMI input is output by the HDMI outputs. You may

want to change this setting to On if your TV is connected

to an HDMI output and you want to listen to audio from

an HDMI component through your TV’s speakers. Nor-

mally, it should be set to Off.

Off:

HDMI audio is not output (default).

On:

HDMI audio is output.

Notes:

• If On is selected and the signal can be output by the

TV, the AV receiver will output no sound through its

speakers.

• When TV Control is enabled, this setting is set to

Auto.

•With some TVs and input signals, no sound may be

output even if On is selected.

• When the AudioTVOut setting is set to On, or TV

Control is set to Enable and you’re listening through

your TV’s speakers (see page 28), if you turn up the

AV receiver’s volume control, the sound will be output

by the AV receiver’s speakers. To stop the AV

receiver’s speakers producing sound, change the set-

tings, change your TV’s settings, or turn down the AV

receiver’s volume.

■

LipSync

The Lip Sync function can automatically synchronize

HDMI audio and video that’s gotten out of sync due to

the complex digital video processing being performed by

your HDMI-compatible TV. With HDMI Lip Sync, the

audio delay required to synchronize the audio and video

is calculated and applied automatically by the AV

receiver.

Disable:

HDMI lip sync disabled.

Enable:

HDMI lip sync enabled.

Notes:

• This function works only if your HDMI-compatible

TV supports HDMI Lip Sync.

•You can check the amount of delay being applied by

the HDMI Lip Sync function on the A/V Sync screen

(see page 72).

■

xvColor

If your HDMI source and HDMI-compatible TV both

support the “x.v.Color,” you can enable “x.v.Color” on

the AV receiver with this setting.

Disable:

“x.v.Color” disabled.

Enable:

“x.v.Color” enabled.

■

Control

This function allows RIHD-compatible components

connected via HDMI to be controlled with the AV

receiver.

Disable:

RIHD disabled.

Enable:

RIHD enabled.

Notes:

• RIHD, which stands for Remote Interactive over

HDMI, is the name of the system control function

found on Onkyo components. The AV receiver can be

used with CEC (Consumer Electronics Control),

which allows system control over HDMI and is part of

the HDMI standard. CEC provides interoperability

between various components, however, operation with

components other than RIHD-compatible components

and recommended components cannot be guaranteed.

• Select Disable if a connected component is incompat-

ible or you’re not sure about its compatibility.

• If operation is unreliable when set to Enable, select

Disable instead.

6_Advanced_En Page 75 Wednesday, March 5, 2008 10:20 AM

1 2 ... 70 71 72 73 74 75 76 77 78 79 80 ... 95 96

Commentaires sur ces manuels

Pas de commentaire

ONKYO TX-SR506 Manuel d'utilisateur Page 75

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV ONKYO TX-SR506