ONKYO DV-SP501 Manuel d'utilisateur télécharger pdf (Page 57)

Troubleshooting

If you have any trouble using your DV-SP501, check the following table for possible causes and remedies. If you still

can’t resolve the issue yourself, please contact your Onkyo dealer.

Symptoms Causes Remedies

DVD Player

Can’t turn on the

DV-SP501?

The power cord is not connected.

Connect the power cord to a suitable wall outlet

(page 23).

The [POWER] switch is set to OFF. Set the [POWER] switch to ON (page 23).

External interference is affecting the

DV-SP501’s digital circuitry.

Turn off the DV-SP501, wait ﬁve seconds, then try

turning it on again. If that fails, disconnect the

power cord from the wall outlet, wait ﬁve seconds,

reconnect it, then try turning it on again.

The disc tray won’t close

properly?

The disc is not centered in the disc tray.

Place the disc in the center of the disc tray

(page 26).

The disc is dirty. Remove the disc and clean it (page 10).

Can’t start playback?

No disc is loaded. Load a disc (page 26).

The disc cannot be played because it’s

incompatible.

Use only compatible discs (page 8).

The disc is upside down. Load the disc the correct way up (page 26).

The disc is not centered in the disc tray.

Place the disc in the center of the disc tray

(page 26).

The disc is dirty. Remove the disc and clean it (page 10).

The disc uses parental lock and the Paren-

tal Lock function is on.

Turn off the Parental Lock function (page 48).

The DVD-Video disc is intended for use in

another region.

If the region number on the disc does not match

the region number on the DV-SP501, the disc

can’t be played (page 51).

The picture distorts occa-

sionally?

The disc is dirty. Remove the disc and clean it (page 10).

Yo u’re using the Fast Forward or Fast

Reverse function.

A little picture distortion may occur when using

these functions. This is normal.

Picture instability or noise?

The DV-SP501 is connected to your TV

via a VCR or other video equipment and a

copy-protection system is affecting the

picture.

Connect the DV-SP501 directly to your TV

(page 19).

No picture?

The wrong input source is selected on

your TV.

On your TV, select the input to which the

DV-SP501 is connected.

The video cable is not connected properly.

Check the video cable and correct as necessary

(page 19).

Settings are not saved?

If there’s a power failure, or the power

cord is disconnected inadvertently, any

settings are lost.

Before you disconnect the power cord, set the

DV-SP501 to Standby by pressing the [STANDBY/

ON] button, and wait until “GOOD BYE” has dis-

appeared from the display.

Brightness is unstable or

the picture is noisy?

The DV-SP501 is connected to your TV

via a VCR or other video equipment and a

copy-protection system is affecting the

picture.

Connect the DV-SP501 directly to your TV

(page 19).

Your TV doesn’t support progressive scan-

ning.

Reset the DV-SP501 to its initial settings

(page 45).

Chapters or tracks don’t

play in the correct order?

You are using repeat playback, program

playback, or random playback.

Select normal playback (pages 32–35).

DV-SP501_En.book Page 57 Tuesday, May 20, 2003 4:17 PM

1 2 ... 52 53 54 55 56 57 58 59 60

Commentaires sur ces manuels

Pas de commentaire

ONKYO DV-SP501 Manuel d'utilisateur Page 57

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de DVD ONKYO DV-SP501